Charge All Models Of The Leapmotor C10 With An EV Charger That Can Connect To Multiple Power Sockets
The Type 2 multi adapter EV charger can connect to 1 Phase and 3 Phase sockets, thus allowing a maximum current of up to 22kW. The adapters that are available to buy for this charger will allow one device to charge an Leapmotor C10 with the following power outlets:
3 Phase 32A CEE (Commando) 5 pin socket
3 Phase 16A CEE (Commando) 5 pin socket
1 Phase 32A CEE (Commando) 3 pin socket
1 Phase 16A CEE (Commando) 3 pin socket
13A UK 3 pin socket
16A Euro 2 pin socket
Regardless of whether the power socket supplies more current than the Leapmotor C10 can accept, it is the vehicle that determines the maximum current it draws from the EV charger. This charger will therefore only provide up to the maximum charging capacity that the vehicle can handle.
The multi-adapter charger offers variable current. your EV can be charged at 1 Phase or 3 Phase power with options of 6A, 8A, 10A, 16A, 20A, 24A, or 32A. This universal multi-adapter charger is therefore compatible with (solar panel, Photovoltaic) PV Systems. The device also retains the chosen setting for subsequent charges.
Is This 32a Universal EV Charger Suitable For The Leapmotor C10?
Is This The Right Charger For My EV
The Leapmotor C10 (purchased in Europe) has a Type 2 socket as standard, thus ensuring compatibility with this charger. You can also match your vehicle socket to our photos.
We advise that the electrical socket and supply that is used to charge an EV will need to have been checked by an electrician to make sure that it is suitable for charging an EV for long periods and at variable currents.
Please also check the information at the top of this page, “Please Read Before You Buy”, to help avoid the most common reasons for returning a charging cable.
Please note that the manufacturer of this vehicle did not manufacture this charging cable.
Multi Adapters
The adapters that are available for this multi socket charger allows the Leapmotor C10 to be charged from all 5 pin and 3 pin 32A and 16A CEE sockets. There are also adapters for charging the vehicle with a 3 pin 13A UK (Type G) socket and 2 pin 16A Euro (Type F) socket. The charger will detect the voltage of the power supply so it will auto switch to 1 Phase or 3 Phase power.
This universal charger connects your EV to the most common AC power supplies in the UK and mainland Europe. Therefore, you can charge your Leapmotor C10 using a hookup at holiday parks, campsites or caravan parks. Or, charge your EV at a marina, workplace, or on holiday in Europe.
When using this 32A charger with the adapter / power outlets displayed in the table below, the charger will provide the following maximum currents:
| Adapter & Outlet | Max kW |
|---|---|
| 3 Phase CEE 32A | 22kW |
| 3 Phase CEE 16A | 11kW |
| 1 Phase CEE 32A | 7,4kW |
| 1 Phase CEE 16A | 3,7kW |
| UK 13A | 2,2kW |
| Schuko 16A | 3,7kW |
Please note that the multi-adapter charger can only be set to 10A when using the 13A mains plug. The Schuko adapter is only to be used with the 2 pin Euro (Schuko / Type F) socket.
The maximum current displayed in the above table will not necessarily be the current that the EV / PHEV will accept. That is, the vehicle will only accept up to the maximum AC current of its onboard charger (OBC).
EV Cable Case
This multi adapter charger includes a complimentary EVA cable case, allowing for safe storage of your charger and adapters. The case has an elasticated strap in the bottom compartment and elasticated mesh pocket in the top, providing convenient storage of your charger and up to 5 adapters.
Leapmotor C10 – Universal Charger Features
IP65 protection for the control box. TUV approved.
Control box IK08 crush-tested.
Charging Timer. Set the charger to start charging your EV from 1 to 8 hours. Thus enabling charging during off peak electricity rates.
Type A and Type B residual current fault detection.
Built in fault detection: Over voltage / under voltage, over current, short circuit, EFT and surge protection
PCB Overheating protection: The charging current will automatically reduce if the circuit board in the device box becomes too hot.
7 Optional amp settings: 6A, 8A, 10A, 16A, 20A, 24A and 32A
LCD colour display including real time charging information
Adapters available – 3 Phase CEE plug 32A, 3 Phase CEE plug 16A, 1 Phase CEE plug 16A, 1 Phase CEE plug 32A, 3 pin UK plug 13A and 2 pin Euro Type F, Schuko Plug 16A
3 Phase 32A Universal Charger Technical Data
| Charging cable type | 5-pin red 32A CEE / Commando to Type 2 (IEC 62196-2) connectors |
| Cable lengths available | 5Metre, 8Metre |
| Rated current | 32A max. Adjustable currents: 6A 8A 10A 16A 20A 24A 32A |
| Certification | CE, UKCA, TUV tested |
| Cable from control box power outlet | TPU 5×6+1×0.5mm. Length including plug and adapter: 1 Metre |
| Cable to Type 2 vehicle plug | TPU 5×6+1×0.5mm |
| Control box dimensions | 255mm (H) x 109mm (W) x 65mm (D) |
| IP grade | Control box: IP65. Plugs when connected to sockets: IP55 |
| Operating voltage | 220V-240V AC and 380V-415V AC |
| Leakage protection | AC leakage 30mA. DC leakage 6mA |
| Working temperature | -30°C to 60°C |
| Flame retardant | Control box and Type 2 plug: UL94 LV: Cable: UL1581 LV: VW-1: |
| Insulation resistance | 10MΩ |
| Altitude | -≤2000m |
Reviews
There are no reviews yet